品牌
其他厂商性质
上海所在地
Tianjin BC - 2 plastic impact low temperature embrittlement instrument technology parameters:
Cooling method: compound refrigeration
Cold head size: 190 * 150 * 80 mm
Cold bath volume: 202 * 164 * 118 mm
Temperature: room temperature - 76 degrees
Constant temperature accuracy: + / - 0.5 degrees
After the impact velocity, impact time and impact rate of 200 + / - 5 mm range test 20 cm/s
Working power supply: AC220 plus or minus 10% 50 hz
Sample clamping: 60 slices
天津BC-2塑料低温冲击脆化仪采用进口全封闭与电子制冷相结合的低温制冷器,替代传统的二氧化碳干冰冷剂作为冷浴的冷却手段,根 据GB/T5470(等同于ISO974-80)标准规定的试验方法,测定软质塑料的脆化温度.由制冷压缩机组, 冷浴,冲击装置和温度控制箱三部分组成. 冷浴温度由数字温度控制仪控制,控温精确. 冲击装置采用加速垂直冲击方法.
Tianjin BC - 2 plastic impact low temperature embrittlement tester adopts imported fully enclosed combined with electronic refrigeration and low temperature refrigerator, replace traditional carbon dioxide dry cold agent as a means of cooling, cold bath root according to GB/T5470 (equivalent to ISO974-80) standard test method, to determine the embrittlement temperature soft plastic. The refrigeration compressor unit, cold bath, impact device and temperature control box of three parts. Cold bath temperature is controlled by a digital temperature control instrument, temperature control is accurate. Impact device adopts vertical shock acceleration method.
天津BC-2塑料低温冲击脆化仪技术参数:
制冷方式:复合式制冷
冷头尺寸:190*150*80mm
冷浴容积:202*164*118mm
温度范围:室温— -76度
恒温精度: ±0.5度
冲击速度:冲击时和冲击后5mm范围内试验速度为200±20cm/s
工作电源:AC220±10% 50HZ
试样装夹量:60片
使用方法:
1. 仪器后侧与墙壁的距离不得小于0.5米,有利于制冷压缩机组的通风。
2. 在冷浴内注入工业酒精,酒精的液面应距冷槽口20mm以下,以浸没夹具为好。
3. 请注意仪器接通电源后,冷浴温度由温度控制仪自动控制,冷浴温度开始下降。在降温过程中,应升高冲击锤,使其离开工作介质,以免冲击锤带走冷量。
4. 冲击锤操作方法:
1). 手柄逆时针旋转时,冲击锤上升,注意上升速度不能过快。
2). 冲击锤下降时,手柄顺时针旋转,注意旋转时应迅速,以减少冲击锤下落时升降齿条的阻力。在每次冲击后应将冲锤提起,使其离开工作介质。
5. 温度控制的操作方法:
控温需重新设定时,可按SET设置键,待设定温度指示窗出现SO时即可进行设定,按移位键选定设置位置,再根据需要设定数字按加数键或减数键,设定完毕后再按SET设置键,即可进入自动温度控制状态。
6. 试样的试验操作方法按GB8948,8949-88(人造革)试验方法进行。
7. 制冷压缩机不允许频繁启动,关机后待冷浴温度回到+10℃后才能再启动