德国KAYSEN凯森泵业有限公司

Germany Kaysen Pump Co., Ltd.

凯森泵业总代理：营派阀门（上海）有限公司

详细资料请登录：营派阀门（上海）有限公司

进口不锈钢潜水泵Germany Kaysen

德国KAYSEN凯森进口不锈钢潜水泵概述
不锈钢潜水泵是潜水泵的一种，因为有很多潜水泵的材质是铸铁或者塑料的，如果仅仅用这些材质做出来的潜水泵，就很难满足客户的需求，如有很多有腐蚀性的介质就不能排放，如硫酸、盐酸、硝酸等；这是它的其中一个特点。另外的特点就是除了不生锈外，还耐高温。所以有很多厂家又生产了耐高温不锈钢潜水泵。虽然是不锈钢，但是有很多辅助材料就耐不了多少高温，一般在120°以内是没有问题，如有些化工厂需要耐高温200多度的还是得选用离心泵。

主要特点：

●不锈钢潜水全部采用精密铸造而成，除了能够生产304的以外，还可以生产316、316L、等。

●采用不锈钢设计的排水结构，因为一般污水泵都有一定的腐蚀性和磨损，在设计上采用了耐磨，耐腐蚀的不锈钢作为主要材料，它具有普通潜水排污泵的全部优点，同时增加了耐磨耐腐蚀的特点，扩大了适用范围。

●不锈钢自身有耐高温性能，正常情况下可耐介质温度50度左右，在德国巴赫公司的技术改进上可在100度以下的介质温度定做。

●304的使用范围在PH值4-10之间好用，如果超过该介质，建议使用316或者316L。

●电压除了可以做220V和380V以外，还可以定做440V和660V电压。

KAYSEN不锈钢潜水泵图片展示：

潜水泵日常维护

日常维护潜水泵每天检查电源线。禁止漏水潜水泵运行。每天检查泵体是否损坏，确保电机在工作时不漏气。手术后，应及时清理附在泵上的碎屑，泵清洗。为确保潜水泵正常运行，您必须遵守这些要求。潜水泵使用前，应用兆欧表检查电机的绝缘电阻，zui小值不得低于50M。灌水马达应打开塞子，注满清水，然后拧紧塞子，不要把灌溉塞子直接拧进井里。使用前检查电缆是否有裂纹，以防破裂。如果损坏应该交换，以防止泄漏。潜水泵在进入水中之前应先怠速1-2分钟，启动两次，检查是否正常起动和怠速，转向满足要求。如果转向，而不是交换任何两相接线。检查杨管是否有裂纹，联轴器是否安全。潜水井下井和提升，绝不允许电缆本身，以避免损坏电缆或断开接头，造成不应有的事件。应该用电线或卡板和提升。电源电压应控制在额定电压的±5％范围内，这样电机才能正常工作。如果电压过低或过高，电动机不能继续使用，以免在工作过程中*损坏电机的过电压或欠压。立式潜水泵应浸入水中，不能倾斜。移到水下5米的水深是适当的。高含沙量的潜水泵不得输送水或泥浆。实际水头潜水电泵应在额定电梯的0.8-1.1倍范围内使用，以提高机组效率，节约能源，同时避免电机过载。潜水电动机的接线必须接入现实，避免燃烧电动机运行电动机相。电缆必须经常检查是否有裂纹，划痕等，有及时的更换或修理。如发现机油漏油，应及时向生产厂家进行维修或保养，更换密封件。电动机应定期清洗浸水沉砂池，更换电机内腔水。潜水泵运行六个月后，应进行维护检查，更换损坏的部件。使用潜水泵后，水马达应在马达内部放入净水，将泵抽干净，油锈，并保持直立在干燥的地方。

Submersible Pumps Routine Maintenance

Submersible Pumps Routine Maintenance Check the power cord every day. The absolute prohibition of leakage water submersible pump operation. Checked daily pump body for damage, ensure that the motor does not leak at work. After the operation, you should promptly clean up the debris attached to the pump, the pump rinse. To ensure the normal operation of submersible pump, you must follow these requirements. Submersible pump before use, shall be checked with a megger insulation resistance of the motor, the value of the minimum of not less than 50M. The flooding irrigation motor should open the plug, filled with clean water and then tighten the plug, do not wring out the irrigation plug directly into the well. Check the cable for cracks before use, to break. If damage should be swapped to prevent leakage. Submersible pump should be before launching into the water, then idle for 1-2 minutes and start twice to check whether the normal starting and idling, turn to meet the requirements. If the steering Instead, you can swap any two-phase wiring. Check whether there are cracks Yang pipes, couplings are secure. submersable well pump to go down and lifting, never allow the cable itself, to avoid damage to the cable or disconnect joints, causing undue incidents. Should go down with wire or card board and lifting. Supply voltage should be controlled at the rated voltage of ± 5% range, so the motor to work properly. If the voltage is too low or too high, the motor can not continue to use, in order to avoid long-term motor overvoltage or undervoltage at work when damaged. Vertical submersible pump should be dipping into the water, not diagonal. Moving into the water depth of 5 meters under the water level is appropriate. Submersible pump high sand content shall not transport water or mud. Actual head submersible pump should be used within 0.8- 1.1 times the rated lift in order to improve unit efficiency, energy conservation, while avoiding motor overload. submersible electric motor wiring must be connected to reality, to avoid burning motor running motor phase. The cable must always check whether the cracks, scratches, etc., there is the timely replacement or repair. If motor oil leakage, it is timely to the manufacturer for repair or maintenance, replacement sealing element. Electric motor should be cleaned regularly flooding grit chamber, replace the motor cavity water. Submersible pump running after six months, should maintenance checks, replace the damaged parts. After using submersible pumps, water motor should put a net water inside the motor will pump clean, oiled rust and keep it upright in a dry place. 

进口不锈钢潜水泵Germany Kaysen

位于德国SchwäbischGmünd的凯森Kaysen泵业有限公司是亚欧的各种流体水泵和隔膜泵制造商之一。60多年来，凯森以“德国制造”的可靠性和质量达到了zui高标准。凭借我们全面的产品组合，我们支持亚欧各地的客户成功掌握供水，采矿，工业，化工，造纸，电力，食品，制药，污水和海上行业的苛刻抽水任务。作为上述领域创新技术的供应商，我们是液体需要安全，高效和经济运输的*合作伙伴。
        德国凯森始终坚持“重质量，讲信誉”为宗旨。产品现全国各地，并已逐步开发海外市场。公司多次被评为“重合同讲信用”企业，深得用户的信赖和广泛的赞誉。

        The Kaysen Pumps GmbH in SchwäbischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
          Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.