POB-200F Placid
时间：2017-06-20 阅读：229
Placid工厂商
Placid Industries工厂上海航欧机电设备有限公司中国区（Non-exclusive）
PLACID传动控制器，PLACID离合器 PLACID磁粉离合器PLACID传动控制器，PLACID磁粉制动器, PLACID磁粉离合器, PLACID磁滞制动器, PLACID储存自订离合器和制动器,
PLACID传动控制器 磁粉制动器/离合器：PLACID普莱西德工业公司1973年-成立 , 1981年-制造磁粉离合器和制动器,1990年在欧洲销售通过HucoD ，1994年-制造磁滞制动器,2003年销售大磁粉制动器（千字节）和离合器（架 KC）
PLACID产品特征：由于没有电激励，自由的轴旋转。 随着电子激发，成为轴耦合的情况。 虽然负载转矩小于输出扭矩，轴不会旋转。 当负载转矩的增加，制动将下滑顺着水平的转矩所规定的线圈输入电流。
PLACID公司主要产品：PLACID传动控制器，PLACID离合器 PLACID磁粉离合器PLACID传动控制器，PLACID磁粉制动器, PLACID磁粉离合器, PLACID磁滞制动器, PLACID储存自订离合器和制动器, PLACID
主要型号：
B5ZD
0.003 - 0.063 1.5 11 x 10-9 1.5 0.7 4000 0.2 B5ZD data sheet
B5Z
0.006 - 0.31 16 x 10-8 2 3500 B5Z data sheet
B1
0.04 - 1 2 11 x 10-7 3.5 4 3000 0.6 B1 data sheet
B2
0.05 - 2.5 3 55 x 10-7 8 5 2500 1 B2 data sheet
B6
0.2 - 6 4 23 x 10-6 15 25 2000 2 B6 data sheet
B15
0.3 - 15 6 34 x 10-6 20 2.5 B15 data sheet
B35
0.6 - 35 9 12 x 10-5 30 50 1800 4 B35 data sheet
B60
1 - 60 8 45 x 10-5 50 100 7 B60 data sheet
B115
2.5 - 115 13 61 x 10-5 55 120 8 B115 data sheet
B150
3 - 150 15 x 10-4 80 1300 12 B150 data sheet
B220
4 - 220 18 29 x 10-4 110 1000 21 B220 data sheet
B5Z
B5ZD Options
DXF
-
B1 Options
DXF
B2 DXF
DXF
B6 DXF
DXF
B15 DXF
DXF
DXF
B35 DXF
DXF
DXF
B60 Options
- DXF
B115 DXF
DXF
B150 DXF
DXF
B220 DXF
DXF
MODEL
(Click p/n
to view
photo)
Shaft
Style Torque
Range
(lb.-ft.) 24v
Coil
Maximum
Overhung
Load
(lbs.) Max.
RPM
Weight
(lbs.) Data Sheets
Drawings
Optional
Electric
Fan
Cooling
Input
Current
(amps)
KB-2.5
Solid
0.2 - 15 1.3 90 1800 19 KB-2.5
data sheet
DXF
-
KB-5
0.5 - 38 2 125 31 KB-5
data sheet
DXF
POB-100F
0.5 - 70 2.4 175 79 POB-100F
data sheet
DXF
POB-100F
with fan
POB-200F
2 - 130 2.7 200 128 POB-200F
data sheet
DXF
POB-200F
with fan
POB-400F
4 - 300 3.5 325 225 POB-400F
data sheet
DXF
POB-400F
with fan
PLB-50
Hollow
1.4 - 30 1.25 125 500 17 PLB-50
data sheet
DXF
-
PLB-100
1.5 - 70 2 175 31 PLB-100
data sheet
DXF
PLB-200
4 - 140 2.4 200 62 PLB-200
data sheet
DXF
MODEL Heat Dissipation (Watts) Compressed Air
at
100 RPM * at
1000 RPM with external cooling by: Pressure
(lb.-in.2) Flow Rate
(ft.3 / minute)
Compressed
Air Optional
Electric Fan
KB-2.5 130 175 260 - 4 6
KB-5 190 275 425 - 5 7
POB-100F 300 500 800 9 10
POB-200F 425 800 1200 7 6
POB-400F 550 1200 1900 21 14
PLB-50 160, all RPM 240 - 7 7
PLB-100 200, all RPM 300 - 8
PLB-200 350, all RPM 500 - 9
MODEL
Click p/n
to view
photo
Torque
Range
(lb.-in.) Input
Electric
Power
(Watts)
Slip Heat
Dissipation
(Watts) Maximum
Overhung
Load
(lbs.) Max.
RPM
Weight
(lbs.) Data Sheets
Drawings
C2D
0.01 - 0.31 3 2 4 2000 0.7 C2D data sheet
PDF
DXF
C2
0.06 - 2 6 C2 data sheet
C5
0.19 - 5 5 10 20 3 C5 data sheet
PDF
DXF
CC14-H
0.4 - 14 5 20 35 1400 3.5 CC14 data sheet
PDF
DXF
C15
0.4 - 15 6 5 C15 data sheet
PDF
DXF
C35
1 - 35 10 30 50 1000 9 C35 data sheet
PDF
DXF
C70
1.3 - 70 14 50 80 17 C70 data sheet
PDF
DXF
C130
4 - 130 15 80 22 C130 data sheet
PDF
DXF
MODEL
(Click p/n
to view
photo)
Shaft
Style Torque
Range
(lb.-ft.) 24v
Coil
Max.
Over-
hung
Load
(lbs.) Max.
RPM
Weight
(lbs.) Data Sheets
Drawings
Input
Current
(amps)
KC-2.5
solid 0.2 - 15 1.3 90 1800 21 KC-2.5
data sheet
DXF
KC-5
0.5 - 38 2 125 35 KC-5
data sheet
DXF
POC-100F
0.5 - 70 2.4 175 87 POC-100F
data sheet
DXF
POC-200F
2 - 130 2.7 200 147 POC-200F
data sheet
DXF
POC-400F
4 - 300 3.5 325 259 POC-400F
data sheet
DXF
PHC-50
hollow 1 - 30 1.3 125 1000 26 PHC-50
data sheet
DXF
PHC-100
1 - 65 2.2 175 46 PHC-100
data sheet
DXF
MODEL Heat Dissipation
(watts) Compressed Air
at
100 RPM at
1000 RPM with compressed
air cooling Pressure
(lb.-in.2) Flow Rate
(ft.3 / minute)
KC-2.5 130 175 260 4 6
KC-5 190 275 425 5 7
POC-100F 300 500 800 9 5
POC-200F 425 800 1200 7 6
POC-400F 550 1200 1900 21 14
PHC-50 250 400 -
PHC-100 400 800
Machine: Wire EDM (Electric Discharge Machining) machine
Manufacturer: Vollmer
• Placid part number: B7-24-1ME
• OEM part number: unknown
• Coil: 24 volts, Resistance: 134 ohms
• Case O.D. = 2.00 ", 51 mm
Application - Control tension in wire that cuts metal.
Machine: Wire EDM (Electric Discharge Machining) machine
Manufacturer: Charmilles
• Placid part number: B10-18
• OEM part number: 434234.
Replaces 433833 with no modifications.
• For machines: FI290, FI300, FI500
• Coil: 18 volts, Resistance: 38 ohms
• Case O.D. = 2.36 ", 60 mm
Application - Control tension in wire that cuts metal.
Machine: Photographic film developer
Manufacturer: Kodak
• Placid part number: B35-EK
• Replaces: Qualex 2B4473, Electroid 50-EPB30-11-08S-24
• Coil: 24 volts, Resistance: 50 ohms
• Case O.D. = 3.375"
Application - Tensions roll of film
Machine: Microfiche (microfilm) duplicator
Manufacturer: Photomatrix (product line now owned by Scan-Optics)
Was sold as a Kodak machine.
• Placid part number: B35-12-PH
• OEM part number: Photomatrix 102363
• Coil: 12 volts, Resistance: 18 ohms
• Case O.D. = 3.375"
Application - Tensions roll of film
Machine: Digital Printing Press, Quickmaster Di
Manufacturer: Heidelberg
• Placid part number: B60-HEID
• OEM part number: A4.114.1420
• Coil: 12 volts, Resistance: 18 ohms
• Case O.D. = 4.5 "
Application - Tensions plate material.
Machine: Textile processing machine
Manufacturer: Young Engineering
• Placid part number: B60-YE-1
• OEM part number: 26010101
• Coil: 90 volts, Resistance: 547 ohms
• Case O.D. = 4.5 "
• 2 brakes per machine
Application - Provides drag torque on 1/2 of a roller to maintain web straightness.
Machine: Pipe bending machine
Manufacturer: Eaton Leonard
• Placid part number: B115-EL
• OEM part number: 800469 H, Carriage Brake
• Coil: 24 volts, Resistance: 36 ohms
• Case O.D. = 4.5 "
• 2 to 4 brakes per machine
Application - Holds chain connected to carriage & verticle axis stationary while pipe is being bent.
Machine: Beverage container labeling machine
Manufacturer: Trine
• Placid part number: B150-CMS
• OEM part number: 4516
• OEM machine: 4500
• Coil: 24 volts, Resistance: 55 ohms
• Case O.D. = 5.2 "
Application - Tensions roll of labels, to be put on soda bottles, etc.
Machine: Bagger
Manufacturer: Rennco
• Placid part number: C25-24-W2
• OEM part number: Unknown
• Coil: 24 volts, Resistance: 43 ohms
• Case O.D. = 2-7/8 "
• Must be mounted with shafts horizontal.
Application - Winds edge of plastic web. Powered by Placid Industries power supply PS-24-M
Machine: Digital Printing Press
Manufacturer: Ryobi
Also sold under Xerox name.
• Placid part number: C100-PRST1
• Ryobi part number: 95325004
• Presstek part numbers: 535454528,
535454528-1, 535454528-2, 535454528-3
• Replaces Ogura clutch, part number: OPC 100-01
• OEM machines: Ryobi 3404-DI &
Xerox Docu-Color 233-DI
• Coil: 12 volts, Resistance: 11 ohms
• Case O.D. = 4.5 "
Application - Feeding plate material in digital printing press.
Machine: Rewinder
Manufacturer: CTC International, (formerly Compensating Tension Control)
• Placid part number: C130-90-CTC
• OEM part number: B31159
• Coil: 90 volts, Resistance: 633 ohms
• Case O.D. = 5.20 "
Application - Controls tension on roll. Hollow through-shaft for compressed air, to actuate chuck.
Machine: Digital Printing Press
Manufacturer: Adast (Adamovske Strojirny)
• Placid part number: C100-ADAST
• OEM machine: Adast 557
• Coil: 12 volts, Resistance: 11 ohms
• Case O.D. = 4.5 "
Application - Feeding plate material in digital printing press.
Machine: 35mm Photographic Film Splicer
Manufacturer: Gretag
• Placid part number: 15CC2-24-1F
• OEM part number: 50-350706-001
• Coil: 24 volts, Resistance: 205 ohms
• Case O.D. = 1.437 "
Application - Apply torque to 35mm film bobbin, to determine the direction the film is wound inside the can.
Machine: Daytona USA car racing game
Manufacturer: Sega
• Placid part number: C-Daytona
• Part number: Sega 601-7489
• Coil: 24 volts, Resistance: 31.3 ohms
• Case O.D. = 3-5/8 "
Application - Connects to the steering wheel.
Machine: Docu-Mate II, Microfilm Machine
Manufacturer: Terminal Data Corp. (TDC)
• Placid part number: CC30P-10-1
• OEM part number: 212023
• Coil: 10 volts, Resistance: 5 ohms
• Case O.D. = 3-3/4 "
• 2 clutches per machine
• 1 brake per machine, Placid Ind. p/n B25P-10-1, TDC p/n 212022, not shown
Application - Engages motor to belt that transports original paper document.
Machine: Turret-style rewinder
Manufacturer: CTC International, (formerly Compensating Tension Control)
• Placid part number: CC60P-CTC
• OEM part number: P1068-19
• Coil: 90 volts, Resistance: 540 ohms
• Case O.D. = 3.50 "
• 5 clutches per machine
• Special low torque version, CC60-CTC-B, for small rolls & light tension, also available.
Application - Machine winds web onto smaller rolls. The clutch drives the small roll, controlling tension.
Left: Clutch CC60-CTC-B
Special low torque, high RPM version
Rated torque = 30 lb.-in.
Right: Clutch CC60P-90-CTC
Standard version
Rated torque = 60 lb.-in.
Left:
• Placid name: Rotor
• Placid part number: R15P-2
• Accraply part number: 060502
• Replaces Ogura OPC-15
• Case O.D. = 1-5/8 " Right:
• Placid name: Stator
• Placid part number: S15-10
• Accraply part number: 09741
• Replaces Ogura OPC-15-01
• Coil Resistance: 8.4 ohms
• Case O.D. = 4 "
Rotor & Stator (shown assembled)
________________________________________
Rotor:
• Placid part number: R30
• Torque = 30 lb.-inches
• Case O.D. = 2.149"
Stator:
• Placid part number: S30
• Voltage: 6, 12, 24 or 90 D.C.
• Case O.D. = 4"
MODEL
(Click p/n
to view
photo)
Torque
Range
(oz.-in.) Input
Electric
Power
(watts)
Shaft Inertia
(lb.-in.-sec.2) Slip Heat
Dissipation
(watts) Overhung
Load, Max.
(lbs.) Max.
RPM
Weight
(lbs.) Data Sheets
Cover On Cover Off
H3
0.04 - 2.5 2.5 3.8 x 10-6 - 5 1 10,000 0.23 H3 data sheet
H11
0.3 - 11 2 36 x 10-6 9 15 4 9000 0.7 H11 data sheet
H35
0.6 - 35 6 92 x 10-6 15 25 5 8000 2 H35 data sheet
H85
3 - 85 5 560 x 10-6 35 60 40 6000 4.5 H85 data sheet
H140
4 - 140 7 970 x 10-6 45 75 40 5000 6 H140 data sheet
H250
6 - 250 7 290 x 10-5 65 110 50 5000 9 H250 data sheet
MODEL DRAWINGS
H3 DXF
DXF
DXF
H11 DXF
DXF
DXF
H35 DXF
DXF
DXF
H85 DXF
DXF
DXF
H140 DXF
DXF
DXF
H250 DXF
DXF
DXF
PS 24 Volt, 0.75 Amp & 12 Volt, 1.25 Amp versions
For all our small brakes & clutches
• Easy to use - The Span adjustment scales output current for small or larger brakes & clutches.
Control Output Current via -
• Knob (Potentiometer)
• 0-10 Volt Signal - from computer or PLC
• Follower Arm Potentiometer F-12-6
• Ultrasonic Sensor U-B.
The Placid Ind. follower arm or ultrasonic sensor connects to the supply for constant tension unwinding / rewinding applications.
More information >>
________________________________________
PST 24 Volts, 2, 3, 4 Amp versions
For large brakes & clutches or multilple smaller ones.
Control Output Current via -
• Knob (Potentiometer)
• 0-5 volt, 0-10 volt or 4-20mA DC Signal
More information >>
________________________________________
PSH 30 Volts, 2, 3, 5 Amp versions
For large brakes & clutches or multilple smaller ones.
Control Output Current or Output Voltage via - Knob (Potentiometer)
More information >>
MODEL
F-12-6
(Aluminum Case) FM-4-2
(Miniature)
Resistance 500 ohm
Electrical Angle 65 degrees
Mechanical Angle 360 degrees (No stops)
Drag Torque 4 oz.-in. 1 oz.-in.
Overhung Load 20 lbs. 2 lbs.
Download set-up
instructions
Ultrasonic Sensor U-B Specifications
Power Input . . . . . 15-30 VDC, 35 milliamps max.
Powered by Placid Ind. power supply.
Range . . . . . . . . 3.9 - 39.3 inches (100-1000 mm)
Output . . . . . . . 0 to 10 volts D.C., 20 mAmps max.
Push button adjustable endpoints
Resolution . . . . . 0.012 inches (<0.3 mm)
Repeatability . . . . 0.02 inches (<0.5 mm)
Temperature . . . . . 14 to 140°F (-10 to +60°C)
Protection class . . IP67 (Sealed plastic case)
Download detailed set-up directions.
FOR BRAKE
OR CLUTCH
MODEL CUSTOMER SHAFT FLEXIBLE COUPLING DIMENSIONS
Diameter Type Part Number Diameter Length Shaft Gap Type
min. max.
B5Z 3/16 clamp J16-3-2 0.63 0.80 0.02 0.40 Beam
B1, C2 J19-3-3 0.75 0.90
B2 1/4 J22-4-4 0.88 1.06 0.46
C5 5/16 J25-5-5 1.00 1.25 0.65
B6 3/8 J28-6-6 1.13 1.50 0.91
B15, C15 3/8 2 flats at
90 degrees J33-F37-F37 1.31 1.89 0.71 0.78 Oldham
B35, C35 1/2 J41-F50-F50 1.63 2.00 0.60 0.66
B60 3/4 3/16 keyway J50-C75-K75 1.97 2.35 0.72 0.79
2 flats at
90 degrees J50-C75-F75
C70 3/4 3/16 keyway J50-K75-K75 1.97 2.35 0.72 0.79
2 flats at
90 degrees J50-K75-F75
B115, B150
B220,C130 3/4 3/16 keyway J57-K75-K75 2.25 3.07 0.83 0.91
7/8 J57-K75-K87
KB & POB (large brakes) &
KC & POC (large clutches) View large series of couplings.
Model Rated Torque Drawings Photographs
Data Sheets
Solid Shaft Hollow Shaft
1 Side 2 Sides
B5ZD 1 oz.-in. Options
B5ZD-2 / B5Z-2
drawing
Not
Available B5Z, B5ZD photo
B5ZD data sheet
B5Z 5 oz.-in. B5Z data sheet
B1 16 oz.-in. Options
B1-2 drawing
B1 photo
B1 data sheet
B2 40 oz.-in. B2-1 drawing
B2-2 drawing
B2 photo
B2 data sheet
B6 6 lb.-in. B6-1 drawing
B6-2 drawing
B6 photo
B6 data sheet
B15 15 lb.-in. B15-1 drawing
B15-2 drawing
B15-H drawing
B15 photo
B15 data sheet
B35 35 lb.-in. B35-1 drawing
B35-2 drawing
B35-H drawing
B35 photo
B35 data sheet
B60 60 lb.-in. B60-1F drawing
B60-1K drawing
Not
Available B60-H drawing
B60 photo
B60 data sheet
B115 115 lb.-in. B115-1 drawing
B115-H drawing
B115 photo
B115 data sheet
B150 150 lb.-in. B150-1 drawing
B150-H drawing
B150 photo
B150 data sheet
B220 220 lb.-in. B220-1 drawing
B220-H drawing
B220 photo
B220 data sheet
KB-2.5 15 lb.-ft. KB-2.5 drawing
Not Available KB-2.5 photo
KB-2.5 data sheet
KB-5 38 lb.-ft. KB-5 drawing
KB-5 photo
KB-5 data sheet
POB-100F 70 lb.-ft. POB-100F - no fan
POB-100F photo
POB-100F
data sheet
with 110v fan
POB-100F photo
with fan
with 220v fan
POB-200F Placid 130 lb.-ft. POB-200F - no fan
POB-200F photo
POB-200F
data sheet
with 110v fan
PFB-200F photo
with fan
with 220v fan
POB-400F 300 lb.-ft. POB-400F - no fan
POB-400F photo
POB-400F
data sheet
with 110v fan
PFB-400F photo
with fan
with 220v fan
PLB-50 30 lb.-ft. Not Available PLB-50 drawing
PLB-50 photo
PLB-50 data sheet
PLB-100 70 lb.-ft. PLB-100 drawing
PLB-100 photo
PLB-100 data sheet
PLB-200 140 lb.-ft. PLB-200 drawing
PLB-200 photo
PLB-200 data sheet
________________________________________
Magnetic Particle Clutches
Model Rated Torque Drawings
Photographs
Data Sheets
C2 2 lb.-in. C2 drawing
C2 photo
C2 data sheet
C5 5 lb.-in. C5 drawing
C5 photo
C5 data sheet
CC14 14 lb.-in. CC14-HM drawing
CC14-HM photo
CC14 data sheet
C15 15 lb.-in. C15 drawing
C15 photo
C15 data sheet
C35 35 lb.-in. C35 drawing
C35 photo
C35 data sheet
C70 70 lb.-in. C70 drawing
C70 photo
C70 data sheet
C130 130 lb.-in. C130 drawing
C130 photo
C130 data sheet
KC-2.5 15 lb.-ft. KC-2.5 drawing
KC-2.5 photo
KC-2.5 data sheet
PHC-50 30 lb.-ft. PHC-50 drawing
PHC-50 photo
PHC-50 data sheet
KC-5 38 lb.-ft. KC-5 drawing
KC-5 photo
KC-5 data sheet
PHC-100 65 lb.-ft. PHC-100 drawing
PHC-100 photo
PHC-100 data sheet
POC-100F 75 lb.-ft. POC-100F drawing
POC-100F photo
POC-100F data sheet
POC-200F 130 lb.-ft. POC-200F drawing
POC-200F photo
POC-200F data sheet
POC-400F 300 lb.-ft. POC-400F drawing
POC-400F photo
POC-400F data sheet
________________________________________
Hysteresis Brakes
Model Rated
Torque
(oz.-in.) Drawings Photographs
Data Sheets
Solid Shaft
1 Side 2 Sides 1 Side
H3 2.6 H3-1 drawing
H3-2 drawing
H3-3 drawing
H3 photo
H3 data sheet
H11 11 H11-1 drawing
H11-2 drawing
H11-3 drawing
H11 photo
H11 data sheet
H35 35 H35-1 drawing
H35-2 drawing
H35-3 drawing
H35 photo
H35 data sheet
H85 85 H85-1 drawing
H85-2 drawing
H85-3 drawing
H85 photo
H85 data sheet
H140 140 H140-1 drawing
H140-2 drawing
H140-3 drawing
H140 photo
H140 data sheet
H250 250 H250-1 drawing
H250-2 drawing
H250-3 drawing
H250 photo
H250 data sheet
Models H11 thru H250 have the Placid Industries Cog-Buster which keeps slip torque smooth.
________________________________________
Power Supplies
Model Style Drawings
Photographs
Instructions
PS Open PS & PS-M
drawing
PS photo
PS instructions
PS-M Open,
with ammeter PS-M photo
PS-M instructions
PS-MC Enclosed PS-MC
drawing
PS-MC photo
PS-MC instructions
PST Enclosed,
aluminum case PST
drawing
PST photo
PST instructions
PSH Enclosed,
bench-top - PSH photo
PSH instructions