BAY51-Q（BYS）防爆防腐全塑荧光灯（防水防尘防腐防爆） 防爆荧光灯，BYS防爆防腐荧光灯，BAY51-Q防爆防腐全塑荧光灯
BAY51-Q （BYS） explosion-proof plastic fluorescent lamp （waterproof and dustproof anticorrosive explosion-proof）
防爆荧光灯,BAY51-Q防爆防腐荧光灯,BYS防爆防腐荧光灯,防爆荧光灯厂家
Explosion-proof explosion-proof fluorescent lamp, BAY51-Q fluorescent lamp, BYS explosion-proof fluorescent lamp, explosion-proof fluorescent lamp
一、用途
A, use
BAY51-Q（BYS）防爆防腐全塑荧光灯（防水防尘防腐防爆）根据GB3836.1-83《爆炸性环境用防爆电气设备 通用要求》、GB3836.2-83《爆炸性环境用防爆电气设备 隔爆型电气设备“d”》、GB3836.3-83《爆炸性环境用防爆电气设备 增安型电气设备“e”》、的规定设计制造。防爆标志为edⅡCT6，适用在爆炸性气体混合物危险场所1区和2区可燃性气体蒸气ⅡC级T6组及以下场所照明使用。本灯具外壳为塑料外壳，外露金属安装零件为不锈钢，金属部件涂塑处理，防爆性能好，适用于有腐蚀性气体的环境内的作业照明。事故断电情况下应急照明。
BAY51-Q （BYS） explosion-proof plastic fluorescent lamp （waterproof and dustproof anticorrosive explosion-proof） according to GB3836.1-83 "electrical apparatus for explosive gas atmospheres General requirements", GB3836.2-83 "electrical apparatus for explosive gas atmospheres flameproof electrical apparatus" d "," GB3836.3-83 "electrical apparatus for explosive gas atmospheres increased safety electrical apparatus" "e", the design and manufacturing requirements. Explosion-proof mark ed II CT6, suitable for use in lighting the dangerous sites with explosive air mixture zone 1 and zone 2 combustible gas steam II C T6 group and the following places. The lamp shell is a plastic shell, exposed metal parts are stainless steel, metal parts, plastic processing, good explosion-proof performance, suitable for corrosive gas environment task lighting. Lighting emergency power-off condition.

BAY51-Q（BYS）防爆防腐全塑荧光灯主要技术参数
Two, the main technical parameters
1．型号含义
1 types of meaning
BAY51-Q—□×□Y□□□
BAY51-Q Y □ □ □ *
F2—防强腐蚀
F2 - resistant to strong corrosion
X：吸顶式安装
X: ceiling mounted
G：吊杆式安装
G: derrick installation
J：管夹式安装
J: pipe clamp mounting
B：墙壁式安装
B: wall mounted
C：悬臂式安装
C: cantilever installation
S：双脚荧光灯
S: feet fluorescent lamp
D：单脚荧光灯
D: single foot fluorescent lamp
带应急功能
With emergency function
功率
Power
全塑
All plastic
荧光灯
Fluorescent lamp
防爆
Explosion-proof
2．额定工作电压（V）：正常照明AC220 应急照明DC 7.2
2 rated working voltage （V）: normal lighting and emergency lighting DC 7.2 AC220
3．正常照明功率（W）： 20×2，40×2
3 the normal illumination power （W）: 20 x 2, 40 x 2
4．应急功率（W）：20，40
4 emergency power （W）: 20, 40
5．应急灯起动时间（S）：0.3
5 emergency lamp starting time （S）: 0.3
6．充电时间（h）：30
The 6 charging time （H）: 30
7.应急灯照明时间（h）：1
7 emergency lighting time （H）: 1
8．防护等级：IP55
8 protection grade: IP55
9．引入电缆外径（mm）：Ф10
9 introduction of cable diameter （mm）: 10
BYS-Q1×20 AC220V ExedmⅡCT6DIPA20TA,T6 G3/4″ φ10～φ14mm IP65WF2
BYS-Q1 * 20 AC220V Exedm CT6DIPA20TA, T6 G3/4 "dia 10 to 14mm IP65WF2
BYS1×20（18W）
BYS1 * 20 （18W）
BYS-Q1×40 1×40（36W）
BYS-Q1 x 401 x 40 （36W）
BYS-Q2×20 2×20（18W）
BYS-Q2 x 202 x 20 （18W）
BYS-Q2×40 2×40（36W）
BYS-Q2 x 402 x 40 （36W）
额定电压 应急照明时间 充电时间 应急起动时间 应急功率
Rated voltage emergency lighting time charging time emergency starting time of emergency power
正常电压
Normal voltage
AC220V 应急电压
AC220V emergency voltage
DC6V 90min 24h 0.3S 20W（1×18）
DC6V 90min 24h 0.3S 20W （1 * 18）
40W（1×36）
40W （1 × 36）
BAY51-Q（BYS）防爆防腐全塑荧光灯主要技术性能和结构
Three, the main technical performance and structure
全塑防爆应急荧光灯为增安型外壳，有良好的防护性能，对可能产生火花的部件采取专门的保护措施以提高安全程度。
Full plastic explosion-proof emergency fluorescent lamp of Increased-Safety shell, has good protective properties, take protective measures specific to produce sparks components in order to improve the safety level.
1．灯具的后罩材料为玻璃纤维增强塑料，透明罩的材料为聚碳酸酯，抗冲击性强，防腐蚀性能好，重量轻。
1 lamp cover material is glass fiber reinforced plastic, the transparent cover material is polycarbonate, strong shock resistance, good corrosion resistance, light weight.
2．塑料外壳能承受28昼夜高温高湿和1昼夜低温的热老化试验，而不影响防爆性能。塑料外壳为燃阻性材料，通过960℃炽热丝试验，水平燃烧试验，ISO1210试验。后罩壳具有抗静电性能。
2 plastic casing can withstand 28 diurnal temperature aging test of high humidity and 1 days low temperature heat, without affecting the explosion-proof performance. Plastic shell for fire resistant material, through 960 ℃ hot wire test, horizontal burning test, ISO1210 test. After the shell with antistatic properties.
3．灯具内装有断电开关，确保安装和维修时处于断电状态。
Power-off switch is provided with 3 lamp, in the off state to ensure that the installation and repair.
4．灯具维修和换装光源方便，用钥匙操纵锁扣装置，就可打开透明罩壳，进行操作。
4 lamp repair and replacement of light and convenient manipulation, locking device with the special key, you can open the transparent shell, operation.
BAY51-Q（BYS）防爆防腐全塑荧光灯安装和保养
Four, installation and maintenance
1．进线为电缆布线。电缆布线时导线的引入密封采用橡胶圈压缩密封方式。选用1KV4芯VV型电力电缆引入线时采用同心可剥离扩孔密封圈，用户可根据电缆直径需要逐一剥离密封圈孔的内层进行扩孔。无导线引进出线孔用盲孔垫片和垫圈密封堵塞。
1 in line for the cable wiring. Cable wiring wire into the sealed with rubber ring compression seal. The peelable sealing ring concentric reaming with 1KV4 core VV power cable into the line, the user can according to the inner diameter of the cable hole required by stripping ring hole. No wires into blind gasket and gasket sealing plug with wire holes.
2．接线：灯具两端都可进线，也可一端出线。用钥匙操纵锁扣装置。打开透明罩和反光板，将导线插入在灯具内的接线端子上，然后旋紧。电气原理图见图2、图3。
The 2 wiring: lamp at both ends into the line, also can end line. Locking device control key. Open the transparent cover and the reflecting plate, to insert the wire connecting terminal in the lamp on, then. Electrical schematic diagram shown in Figure 2, figure 3.
3．接线时应使应急控制器始终处在供电状态，给电池组充电，断电时电池组能立即向灯管供电。注意：电源L1一定要接在外接开关电源前级。
The 3 wiring should be always in the state of power supply emergency controller, to charge the battery, power battery can immediay to the lamp power supply. Note: L1 power supply must be connected with switching power supply in the first grade.
4．为保证灯具正常工作和安全，用户应注意
4 in order to guarantee the normal work and safety of lamps and lanterns, the user should note
（1）非专业人员不准打开灯具，开启钥匙应有专业人员妥善保管；
（1） non professional personnel are not allowed to open the lamp, open the key should have professional safekeeping;
（2）不要随便拆卸紧固零件；
（2） do not remove fastening parts;
（3）清洁时，只能用湿布揩擦以防止产生静电，并避免使用化学清洗刘；
（3） when cleaning, only with a damp cloth wipe to prevent the generation of static electricity, and avoid the use of chemical cleaning liu;
（4）检查灯具电器是否处于良好状态；
（4） check the lamps are in good condition;
（5）安装和换光源，不要损坏透明罩壳和反光板；
（5） installation and changing light source, do not damage the transparent shell and the reflecting plate;
（6）在出厂之日起，若没有使用应每隔2-3个月充电一次，充电时间不能少于24h；
（6） on the date, if there is no use should be charged once every 2-3 months, the charging time of not less than 24h;
5．易损件橡胶电缆和电缆密封圈，厂方可提供配件，密封圈硬度为邵尔氏45~55度。
5 the vulnerability of rubber cables and cable sealing ring, the sealing ring can provide fittings, hardness of shore's 45~55.

专业生产：防爆配电箱,铸铝防爆箱,不锈钢防爆箱,防爆接线箱,防爆照明配电箱,防爆动力配电箱,防爆配电柜,防爆控制箱,BZC51防爆操作柱,防爆应急灯,防爆荧光灯,防爆无极灯厂家,防爆正压柜,防爆投光灯,柳市防爆箱,防爆断路器等，质量三包，凡购买本公司产品，质保三年，本公司证件齐全，价格实惠！